This post was most recently updated on September 12th, 2021
Ad optimization should start on a solid foundation, which includes planning where to place your ads, ad sizes to run, maximum and minimum count of ads per page, choosing ad formats, while providing users the best user experience. In this article, we’re going to share tips and tricks, and best practices on ad placement.
Using the right tool to deploy your tags matters as much. When it’s straightforward and user friendly, you save time and can focus on other important tasks. You should also be ready to debug in case any issue comes up after deployment. This entire process brings its own set of challenges, and for as long as you know the direction you’re going for, it should be easier to manage.
Deciding on ad placements is not a one-shot deal. It requires a lot of data analysis and constant changes until you’re fully satisfied with the numbers you see. Every site is unique, and you should be able to strategize around improving ad performance without compromising user experience.
(Filter by device category: Desktop, Connected TV, Setup Box first, then Smartphone, Feature Phone, Tablet)
If no GAM, but you have AdSense, run a report on AdSense (or request the publisher to provide the report if you don’t have access). Follow the setup below to see the Active View Viewable %.
There’s more you can do with Google Ad Manager, and Google AdSense reports. Check out PubGuru University.
Pay attention to the bad performing ones – low viewability % (less than 50%) is usually where the opportunity lies.
Also, pay attention to the volume of traffic (Total code served count). Negligible numbers are most likely cached and not an indication of the inventory being active. Focus only on the ones with decent traffic volume.
If you are currently running a single sized ad unit, consider adding more sizes in the mix and make it flexible. When multiple ad sizes are configured, they all compete in the auction, and the best paying size wins. When choosing which ad sizes to run, consider the following:
1) Spot where the ad is to be deployed (e.g. can’t run horizontal ads on a sidebar, and vice versa)
2) The top-performing ad sizes:
Desktop: 970×250, 970×90, 728×250, 728×90, 336×280, 300×250, 300×600, 160×600
Mobile: 320×50, 320×100, 300×250, 336×280
3) Smaller ad sizes usually perform worse than the bigger ones. On mobile, add 300×250 to the mix where applicable.
Above-the-fold doesn’t necessarily perform better than Below-the-fold. Depending on your site layout, users tend to scroll down right away to consume your content. The following spots potentially perform best:
1) Mid-content (in between paragraphs)
2) Right below or above an image content
3) Close to navigation links or buttons
4) Sticky units
Use these questions as a guide:
1) What is the user trying to accomplish on your site?
2) What do they do when they land on a specific page?
3) Where do they focus their attention?
Help yourself by correctly naming your ad units, making it easier to optimize and manage. When you run reports, or do random quality checks on-site, ad unit names should make sense. If you currently have confusing ad unit names, create a new set! Don’t just change the name of the pre-existing ones. Ad unit code is not editable, and it’s highly recommended for the name & ad unit code to match (applies to those using Google Ad Manager).
Number of ads to run
Although Google has removed the restrictions in terms of the number of ads/page, they recommend at least a 50:50 ratio of ads to content. You may have fewer ads than content, but never more ads than content. The magic number is 5 (five). Once you implement more than 5, you’ll start seeing performance plummeting. The Law of Diminishing Returns also applies here. Competition starts to loosen up. Buyers won’t bid high CPMs anymore because they still get the opportunity to display their ads, given the many available ad slots.
Rule of thumb: Do not implement more than five ad units per page unless essential (e.g., lengthy content).
For mobile, put a single ad unit at the bottom (sitting right above the fold), then skip a screen height → then another ad unit → another screen height → another unit → , etc., up to 5 units.
Intrusive ads (e.g., outstream)
This type of ad can be an incremental revenue source but can negatively impact your other ad units. When it covers the ads, viewability and CTR drop, and CPMs follow along. When running non-standard ads, do it slowly, testing one section at a time and closely monitoring performance per ad unit.
Run your Google Analytics report and look at your:
All these are key performance indicators of your site’s content quality. When users are not engaged, they are not engaged with your ads either. Revisit these metrics and identify how you can get users to stay longer and browse more pages.
Google’s research has found that 53% of mobile web visitors leave if a webpage doesn’t load within three seconds. Ouch! Use PubGuru Ad Inspector to troubleshoot issues in real-time that could be affecting your site speed. Also, check out https://developers.google.com/publisher-ads-audits.
Below are some of the best practices on ad placement. Again, every site is unique, and some of these recommendations might not apply to you. Nevertheless, it’s a good starting point.
GAM: 970×250, 970×90, 728×90, 728×250
AdX hardcoded: 970×250
GAM: 728×90, 728×250, 300×250, 336×280
AdX hardcoded: 728×250
GAM: 300×600, 300×250, 336×280, 160×600
AdX hardcoded: 300×600
GAM: 728×90, 970×90
AdX hardcoded: 970×90
Monitor performance per ad unit after going live. If using GAM, run a Historical report, break it down by Ad Unit, and by date. Be on the lookout for any weird spikes or drops. Expect the numbers to drop initially and should slowly stabilize as days go by.
To calculate your Unfilled Impressions %:
=Unfilled impressions / Total ad requests
Learn more about the important metrics you should pay attention to and how to address abnormal fluctuations in PubGuru University.
With this guide, you’ll be able to become an expert with ad placements! However, it does take a lot of work, knowledge, and tweaking to get everything working as it should. If you don’t have the time to test and manage your ad placements for optimal performance, let MonetizeMore do it for you! We’ve got teams of ad optimization experts working around the clock to maximize ad revenue for our publisher partners. Are you ready to take your ad revenue to the next level? Try a smarter reports by PubGuru today
Here’s the course that 300+ pubs used to scale their ad revenue.